It has been driving for 6 or 7 years in a blink of an eye. This car really makes me love and hate. Needless to say, I believe the owner can understand. What I hate is that there are frequent minor problems after the mileage, and most of them are problems caused by material technology. The problems are not big, but it is a bit disgusting to waste money and time.
A few years ago, I saw what everyone said about return pipe fracture, and I didn’t take it seriously at all. Unexpectedly, at 60,000 kilometers, I was really thrown on the road because of the broken pipe. From then on, I began to pay more attention to all kinds of problems warned by everyone in the forum, and also started to buy oil and materials to maintain myself, and solved all kinds of small problems by myself. I never went out to do it myself. I even bought a small Alto to disassemble and install it. From I didn’t know the sleeve before to a lot of auto repair tools now, I have gradually developed driving into my only hobby besides fishing. Most of the time, I enjoy the process of solving problems and save money by the way. Sometimes when I look at my son’s house full of toy cars, I really feel that cars are men’s toys for life.
In fact, the lid was changed in November last year. I wanted to open it for a while to see if there were any problems. As a result, it was delayed again and again. Now it has been opened for 6 thousand kilometers, and everything is normal. I must hand in my homework, which is also a souvenir for myself!
Pick something important before you start:
1. The oil circuit involved in this operation is dangerous, so the power must be cut off first, and the battery is located on the right side in the trunk! ! !
2, the owner of a BMW must have: ISTA software, with 20 g installation files and more than 100 g installed. It is recommended that a fish be bought directly, which is very cheap and convenient.
3. Torque wrench. There was a 10-150nm wrench before. Because some screws have single-digit torque in this operation, I bought a 5-60nm wrench for accuracy.
4. BMW star-shaped sleeve. At that time, I didn’t buy a sleeve because I had a simple star-shaped 7-shaped wrench. As a result, a screw was not screwed in place, which was almost tragic (detailed later)
5, ratchet wrench, hexagonal sleeve, I have all kinds of ratchets, not big brands, very cheap. Electric wrenches, hand drills, etc. If there are elastic screws, it will save a lot of effort.
I have been studying online for a long time before I started, and I have a good idea of all links, and the tools and materials are also available. I can’t wait to itch. Finally, I specially arranged for two days, which started on a sunny morning! Because of the whole operation by one person, I can’t see the photos completely now. Please forgive me!
The scene of the crime was in a shed where sundry goods were kept in my hometown. I usually live in the city and come back to repair my car, mainly because I am afraid of being disturbed: if someone is watching or even talking, it will affect my state and I can’t concentrate. Second, I’m afraid that there may be no sandstorm or rain outside one day. After all, turn on the engine and don’t get into the sandstorm and dust. However, there is a big hidden danger that if you can’t start the car after you finish it, it is not good to tow it. (Yes, I’m ready to roll over.)
Without a notebook, it is also very convenient to put a PC with a small host on the tool cart. As a non-professional, it is necessary to operate strictly and scientifically to avoid overturning as much as possible! Open ISTA to escort the next operation.
Remove all the engine decorative covers, and then remove the adhesive tape and the left and right covers at the position shown in the figure.
Then remove the tie rod as shown in the picture, and forget to shoot it. Note that the position of 1 should be pried open, there are screws under it. Remember to loosen these big screws. I used a new electric wrench. Wow, it’s so easy. The tightening torque is 56NM, and a torque wrench can be used for installation.
It is reasonable to say that everything blocking the valve cover should be removed. ISTA said that this soundproof sponge should be removed. I didn’t remove it, but it didn’t affect much, but it seemed to be torn a little.
The cover is located here, and all kinds of plugs and pipes that get in the way should be removed.
All kinds of plugs, once pulled out, many have to be tilted with the help of a flat screwdriver, with a little ingenuity. Pay attention to the age of the car, the plastic is not so strong, don’t be too violent and be careful to damage it.
This board is in the way, you’d better remove it. Be careful when loosening the screws in the circle, and it will fall easily.
Dismantle the ignition coil and spark plug. Everything that gets in the way has been removed. The four-cylinder spark plug has never been removed so smoothly.
There was obvious oil leakage around the oil filler, and then a washer was replaced, and the problem remained!
Loosen the high-pressure oil interface connecting the oil rail, and find an old piece of clothes to wrap around to prevent gasoline from leaking out.
The red circle is the oil rail, and the green one is the high-pressure oil circuit.
Now it’s one of the biggest difficulties in this operation. The formal process is to first remove this row of small screws, remove the fuel rail, then remove the fuel nozzle with special tools, and then connect the fuel nozzle and the fuel rail according to strict requirements when installing. The whole process is very complicated, which will make you flinch. And my method is as shown in the figure: directly remove the whole fuel rail and fuel nozzle with a crowbar, and skip this most complicated part of the operation! (The method comes from the foreign great god of tubing, thanks to the inspiration of the great god)
The fuel rail is very strong. If you don’t trust it, put something on the contact surface between the pry bar and the fuel rail, slowly apply force, and tilt the left side and the right side.
I peed after a general look.
Carefully tilted for a long time, and then slowly pulled out after loosening, which felt wonderful.
It was so dirty, I searched temporarily for how to clean it, but I gave up without tools. Later, I wiped the outside with clean paper very carefully.
Both the high-pressure oil pump and the pipe are removed. By contrast, this operation is too simple. Remember to pad something, or gasoline will spill.
Then came another difficulty. To remove the VANOS solenoid valves of the two camshafts, which are located in the red line area facing the cockpit, it is extremely difficult to pull out the plug. After a long time of observation with various flat screwdriver and endoscope, it was unsuccessful, and the clip of the plug was also broken, let alone unscrewed the two solenoid valves.
This is the plug shape photographed by endoscope, which is actually similar to the plug of spark plug ignition coil. I don’t know how professionals unplug the plug, or just unscrew the solenoid valve. Without special tools, I screwed and used various tools for a long time, but I didn’t succeed. Later, when I was too tired at night, I went to bed and prepared to get up the next day!
I feel like it’s getting dark when I’m doing nothing. In fact, I’ve been doing this job for almost a day. When I’m tired or hit a bottleneck, I’ll smoke a cigarette or brush my mobile phone, or even lie in bed for a while. Professionals estimate that it will be done in an hour or two. Again, we don’t work to make money, but we enjoyed the process.
In the evening, I searched a lot of maintenance videos, all of which were to remove the solenoid valve first, which led me to get up early the next morning or continue my previous thinking. After all kinds of attempts, I still couldn’t remove either the solenoid valve or the plug, so I wanted to put it back as it was from time to time! But it is really unwilling to go here!
(In order to avoid falling into sundries, I stuffed all the holes exposed on the cover with dust-free paper, not toilet paper.)
I don’t know if it was God’s blessing. Just when I was in a desperate situation and almost gave up, I suddenly thought of another plan: since the connected pipes are all soft, it is not bad to remove the cover first!
When you have the idea, the rest is easy to say. Loosen each screw according to the prompt.
Although the screws have been loosened, the combination is still quite tight. Carefully separate the four sides, carefully avoid all obstacles, slowly find the angle to lift the lid out a little, and finally open it! (It’s easy to say, but it actually took a long time.)
The white clip of a plug has been broken by me.
This annoying plug, once you ignored me, now you and I don’t care, so we can easily unplug it.
Just like the goddess took off the only gauze, my heart came and went at that time. . . . Look at it carefully for a long time
Camshaft, timing chain, valve stem. . . The understanding of the engine is further deepened.
The sealing washer should be carefully removed, and the contact surface should be carefully cleaned with dust-free paper.
I also thought of the kind of words that everyone loves to ridicule, "The use of water and oil causes the engine to open the cylinder." . .
Haha, there are too many common cognitive misunderstandings caused by various factors, which require you to have the ability to question and think independently!
When you understand many things, you often fall into pain. . . Uh … . Digress
The next step is simple, take out the new cover that has been prepared for a long time.
Screw on the solenoid valve. It should be noted here that I have tried several times. After screwing on the solenoid valve, one of the clasps in the figure will be displaced every time, so it is necessary to manually break the clasps back to the correct position. That is to say, if you don’t remove the cover, directly replace the solenoid valve, even if there is a special disassembly and installation tool, there is a great chance that it will not be installed in place, and you still can’t see it. I don’t know what hidden dangers there will be!
Besides, I didn’t notice that my solenoid valve was "goo" until I finished it. . Goo. 。” The croaking of frogs is very common on the Internet. It can be solved by replacing the solenoid valve, but it’s too lazy to disassemble it after it’s installed. I don’t feel any other abnormalities at ordinary times. Let’s leave it on first.
This is the old cover that has been removed. Basically, there are cracks in the position shown in the figure, which causes oil to penetrate into the first and second cylinders, causing oil consumption and oil immersion in the spark plugs of the first and second cylinders!
This is an oily two-cylinder spark plug before replacing it. I checked it once after driving for two or three thousand kilometers. It was extremely dry. I couldn’t find the photo. I will make it up another day!
When installing a new cover, the rain deflector in the red circle is a little in the way and wants to be removed. Who knows that the position of the green circle is too tight to be removed and it won’t rain, so give up. Later, it was found that the wiper needs a lama, which has been purchased and can be removed next time!
Tighten all the screws in strict accordance with the requirements in sequence. I screwed them twice as required. The first time, I screwed them half a turn, and the second time, the torque was 8nm. That’s the good thing about doing it yourself. You can twist it as you want! Outside the repair shop or even the 4S shop, there is a high probability that it will not be so careful.
Take advantage of the gap to wash the spark plug again, and the insulating silicone grease that has been bought for a long time also comes in handy.
Return all the parts and plugs in the same way, so I won’t go into details, but I don’t know where this screw is installed.
After searching for a long time, I found that the oil inlet pipe was fixed here. It was almost tragic that this screw was not screwed properly.
There is a little trick: install the screws in the disassembly order with the lattice storage box, so it is not easy to add more screws. . .
Everything has been restored, and I have repeatedly checked it several times. The most tense moment is finally coming. Can I light the fire successfully? Do you want to call a trailer?
Bite your teeth and close your eyes. Fight!
Chug chug. . . I have never felt the roar of Bavarian tractors so beautiful! Once successful, my inner sense of accomplishment will overflow, and at that moment my mouth can’t help but rise 45 degrees!
At that time, I even had an impulse to clean this shed, decorate it simply, dig a trench, install air conditioning and lighting, and display my car tools. . . . Wow, what a beautiful picture that is.
Holding back my inner ecstasy, I couldn’t wait to drive out! I should have come back after trying for two or three kilometers, but I was too proud to drive for more than ten kilometers to come back. This is a tragedy.
I’ll go. What’s the matter with the oil stain on the ground? I’m stunned in an instant. Open the cover and check it.
Yes, that’s the last oil inlet pipe screw.
I used a torque wrench to tighten all the screws in ISTA, because there was no star-shaped sleeve, and the last oil inlet pipe screw was screwed with this simple wrench, because the screw was connected with a long head, and the short head was not able to exert force, which led to inaccurate torque estimation, thinking that the tightening was actually not up to standard! Sure enough, there is oil leakage in this position. . . .
Fortunately, there was not much oil leakage when I found it, and I felt a hundred milliliters. It’s a little scary. . . Turning around, I quickly started a whole set of star sleeves, and the money for tools can’t be saved!
After typing so many words, my neck is sore. I turned my head and looked out of the window. It was already dark! I’ve been writing for almost a day, and I wasn’t so serious at school.
Really interest is the best teacher, relying on the knowledge learned online, I completed a self-improvement in auto repair, thanks to BMW’s unreliability for giving me this opportunity hahaha!
Also declare that this post is intended to share experience, not as a specific operational guide. If you need to be extra cautious in operation, it is best to have professionals around you!
Pure manual code word, I hope you like it, don’t spray it if you don’t like it, thank you!
Finally, I wish everyone can have a deep and long-term love with their car.
关于作者